Efibootmgr

Resources

GitHub

Package information

README

EFIBOOTMGR(8)

efibootmgr is a tool for managing UEFI boot entries.

It is not a bootloader. It is a tool that interacts with the EFI firmware of the system, which itself is acting as a boot manager. Using efibootmgr boot entries can be created, reshuffled and removed.

Installation

Kernel

CONFIG_EFIVAR_FS support needs to be enabled.

Note
It is not possible to use efivarfs without the EFI runtime services, which (in case they have been disabled by default, i.e. CONFIG_EFI_DISABLE_RUNTIME=y) can also be enabled by the kernel command-line option efi=runtime.

Emerge

The sys-boot/efibootmgr package does not have any USE flags. All that is needed is to install it:

root #emerge --ask sys-boot/efibootmgr

Configuration

EFI vars

In order to successfully use efibootmgr the EFI variables filesystem must be accessible. This requires that the system has been booted in EFI mode (and not through the firmware's MBR mode) as otherwise the EFI variables themselves cannot be accessed. If the system is in MBR mode, reboot and do what is necessary in order to tell the system firmware to boot in EFI mode. Usually this involved either changing an option in the firmware's settings or selecting an EFI boot entry in the system's boot menu.

When the system is in EFI mode, run the following command to check for the existence of a mounted efivarfs:

root #mount | grep efivars

efivarfs on /sys/firmware/efi/efivars type efivarfs (ro,relatime)

It is mounted read-only (ro) through the sysfs init script), so it needs to be remounted read-write (rw) manually using the following command:

root #mount -o remount,rw -t efivarfs efivarfs /sys/firmware/efi/efivars

Preconditions

If an EFI System Partition (ESP) does not exist, one needs to be created, see EFI System Partition.

Usage

Listing boot entries

When using an older version of efibootmgr the option --verbose or -v is needed:

root #efibootmgr

BootCurrent: 0002
Timeout: 3 seconds
BootOrder: 0003,0003,0002,0000,0004
Boot0000* CD/DVD Drive  BIOS(3,0,00)
Boot0001* Hard Drive    BIOS(2,0,00)
Boot0002* Gentoo        HD(1,800,61800,6d98f360-cb3e-4727-8fed-5ce0c040365d)File(\EFI\boot\bootx64.efi)
Boot0003* Hard Drive    BIOS(2,0,00)P0: ST1500DM003-9YN16G

Creating a boot entry

To create an EFI boot entry, a couple of arguments are passed to efibootmgr:

• --create or -c to create a new entry;
• --part or -p followed by the partition number on which the EFI System Partition is hosted;
• --disk or -d followed by the disk on which the EFI System Partition is hosted;
• --label or -L followed by the label to use as the boot entry;
• --loader or -l followed by the path of the EFI image to boot

Important
The path of the EFI image to boot must use \ (backslash) instead of / (forward slash) as path separator.

Important
Additionally, if the ESP was already created by another OS, it might be named differently than /efi/EFI. If an ESP was created by another OS, begin the EFI Boot entry using this directory name, which immediately follows /efi.

Below are some examples of how a UEFI entry can be created. If this is the folder structure:

root #tree /efi/ -L 3

/efi/
└── EFI
    ├── Grub
    │   └── grubx64.efi
    └── Gentoo
        └── bzImage.efi

then the loader paths will be:

root #efibootmgr -c -L "Grub" -l '\EFI\Grub\grubx64.efi'

root #efibootmgr -c -L "Gentoo" -l '\EFI\Gentoo\bzImage.efi'

For instance:

root #efibootmgr -c -d /dev/sda -p 2 -L "Gentoo" -l '\efi\boot\bootx64.efi'

It is also possible to add parameters – maybe not supported by all UEFI implementations - to the kernel's command line:

root #efibootmgr -c -d /dev/sda -p 2 -L "Gentoo" -l '\efi\boot\bootx64.efi' -u 'root=/dev/sda3 initrd=\efi\boot\initramfs.img quiet'

Optionally, additional kernels can be installed and made known to the UEFI firmware. This is especially useful when wanting to test more kernels or to dual-boot with another operating system. These will be shown in the boot selection prompt, normally after a keyboard hotkey is pressed at the right time during system initialization. The latest added entry always gets highest boot priority, so it will be default. If the hotkey combination is unknown, search for official documentation from the computer manufacturer. This information is usually not difficult to find.

Deleting a boot entry

Before deleting an entry, first figure out what ID the entry has.

To delete the Gentoo entry as shown above (which has Boot0002 as the identifier), ask efibootmgr to delete the entry with id 2, passing the arguments --bootnum or -b with the identifier, and --delete-bootnum or -B to delete the entry:

root #efibootmgr -b 2 -B

Removable media

EFI bootloaders on removable media are not configured as boot entries, so efibootmgr is not required. See removable media boot path on the ESP for details.

Removal

Unmerge

root #emerge --ask --depclean --verbose sys-boot/efibootmgr

See also

• REFInd — a boot manager for EFI and UEFI platforms forked from and successor to rEFIt.
• EFI stub — provides instructions on configuring and installing kernels in the EFI System Partition (ESP) of a computer running in EFI mode
• Efivarfs — a filesystem in the Linux kernel that enables users to create, delete, and modify (U)EFI variables
• Alternative 2: efibootmgr in the Gentoo Handbook