Talk:Arduino

Note
Before creating a discussion or leaving a comment, please read about using talk pages. To create a new discussion, click here. Comments on an existing discussion should be signed using ~~~~:

A comment [[User:Larry|Larry]] 13:52, 13 May 2024 (UTC)
: A reply [[User:Sally|Sally]] 13:35, 5 November 2024 (UTC)
:: Your reply ~~~~

Issue with Arduino IDE software

Talk status

This discussion is done as of May 3, 2017.

I have the same issue as one here: http://arduino.stackexchange.com/questions/19310/cannot-find-crtatmega328p . You should change this wiki page according to changes and problems when one want to install arduino IDE software. Sorry, I forgot to sign my comment. --Best, Pál (talk) 17:40, 29 February 2016 (UTC)

Hi Csanyipal, I don't have an Arduino or else I might be able to help. Please remember to sign your comments when leaving messages on talk pages. --Maffblaster (talk) 06:44, 29 February 2016 (UTC)

I just emerge arduino again ( did unmerged it before ).

I open a project into Arduono IDE and want to verify it, but get error message:

/usr/libexec/gcc/avr/ld: cannot find crtatmega328p.o: No such file or directory.
/usr/libexec/gcc/avr/ld: cannot find -latmega328p
collect2: error: ld returned 1 exit status

What can I do to solve this problem? --Best, Pál (talk) 20:30, 1 March 2016 (UTC)

Finally I managed to get working arduino IDE on my Gentoo system. I add tinfo USE flag to the sys-libs/ncurses package, then re-emerge it and now Arduino IDE works out here. --Best, Pál (talk) 19:43, 8 March 2016 (UTC)

Please update the article if instructions were incorrect. This is a place to discuss documentation changes before making them (or if someone reverts your edit). Support can be provided on the Forums or IRC. Nothing left to discuss here. Kind regards, --Maffblaster (talk) 00:22, 4 May 2017 (UTC)

I have the same problem, i changed to "+" tinfo use flag on ncurses, but it is still not working. --Juan Facundo Suárez 10:27 -03:00 , 13/06/2017

I could solve this, deleting '--stable' part of crossdev command line, from arduino wiki: Arduino#Recommended:_Install_the_toolchain_using_crossdev on gentoo wiki, so the command line was:

USE="-openmp -hardened -sanitize -vtv" crossdev -s4 --portage --verbose --target avr

this solved it for me. --Juan Facundo Suárez 22:51 -03:00 , 13/06/2017

I also had to add -mpx:

USE="-openmp -mpx -hardened -sanitize -vtv" crossdev -s4 --stable --portage --verbose --target avr

--Sorin Pânca 09:20 +02:00 , 01/06/2018

Arduino Zero

Talk status

This discussion is done as of 2024-03-31.

The kernel driver for Arduino Zero is also CDC ACM. Could you, please, update the page with this information.

Thanks.

Bugalo (talk) 10:53, 31 October 2021 (UTC)

Does this edit fix this ? -- Ris (talk) 14:35, 31 October 2021 (UTC)

Arduino IDE in Portage is Not Current

Talk status

This discussion is done as of 2024-03-31.

This page states as of 10/18/2023:

Official sources

An up-to-date version of the Arduino IDE is available in the official Gentoo repoisitory:

root #emerge --ask dev-embedded/arduino

According to Arduino's page at https://www.arduino.cc/en/software, the current IDE is at 2.2.1 and the one in Gentoo, 1.8.19 is "Legacy IDE (1.8.X)"

I made the mistake of assuming what was in portage was relatively current. Only after a couple of hours did I realize I had an older version which is missing a critical dependency (Arduino's dependency resolution is faulty, so no error showed up like it would in Gentoo's portage). I'll Jlpoole (talk) 00:31, 19 October 2023 (UTC)